Week 14

To jump straight in from where I left off, I extruded the breast down and use a loop cut to get the detail for the rib cage. Then I crease the edges underneath the breasts to give detail to the under boob.

Then I connected the rib area to the lower part of the torso that I made earlier, I had to change the lower part of the model a bit, due to the amount of polys on the lower part of the body didn't match the top part of the body, which was fine due to the guy in the video had the same issue, so following what he did, I edited the bottom part of the model, by deleting some of the faces then extruding some of the verts upwards, I had a problem where I was getting triangles, which are fine but we want quads so I added in an extra vert so that it made it a quad instead, and I used a loop cut so that the rest of the model had no N-gons. Other then that, there were no other problems, and to finish I made a hole shape in the middle for the belly button, that I will add in a bit.    


To make the belly button I filled in the hole and then used the insert tool to make a smaller circle, lastly I use the cut tool to make an even smaller circle that will give the belly button detail. To get even more detail we can crease the edges to make it stand out from the rest of the body.


Now that the front part of the body is done I move onto the Back area. I start off with extruding 3 verts upwards and then using loop Cut to make more edges that will align with the rest of the body.


Then I Filled in the area, by extruding the verts making sure I had enough verts so that there wouldn't be any triangles or N-gons, on the model. 


The collar bone took a while to do as it is a very weird and complex shape to make, I also had a problem where the high poly models collar bone was way too far forward which meant that I had to change the high poly model, so that I could use the Snapping tool for the lower poly model, whilst I was at it I changed the neck a bit and thickened up the arms as well. For the topology of the collar bone it went very well, I just wanted to add how the Youtuber made the centre of the collar bone in a unique way.
 

Then For the Neck I extrude up until it reaches the top part of the Neck, then I keep extruding faces around the Neck until it has reached the back.


Then I Work on the shoulders which I extrude some Verts to make the shape of the shoulders.


Then to finish off this week with filled in the shoulders, which wasn't too difficult, I did have a little trouble with the topology as I made them quads, but look at what 2AM (Youtuber) did in the video, he made them quads but also it was better topology, as it should move better with that style of topology when it comes to rigging.






 

Comments

Post a Comment

Popular posts from this blog

Week 19

Image
To start this Week I went back to the fringe and edited it around a bit to make it look better, I also added a few extra strands of hair to make it look more detailed and on top of the head I made a Cowlick. I start the Back of the Head by making two long strands of hair, and then editing them slightly so that they don't look too similar, as if the all the hair strands on the back of the head look the same it might look wrong and that it has been fabricated instead of naturel. This time I used the Mirror modifier to make the hair symmetrical, I don't finish the hair though, I just add a few more hairs by using the mirror modifier. Whilst I was making the Hair strands I was still keeping in mind to change the flow of the hair and the direction the bottom of the hair was pointing to make it look more natural. I think it is coming along pretty well, however there are still holes in the hair that people can see through, after watching Darcy's video it was easy to cover up these...
Read more

Week 17

Image
Last Week I had done the feet, this Week I move onto the las body part needed for the model, which are the hands. Yet again I looked at the Youtuber 2AM for how he made the hands, because the model will be consistent if I follow the exact same guide all the way through. Like the foot we will start by making a box and loop cutting (Ctrl + R) it, but this time we will loop cut it 3 times along the Z and Y Axis, and once along the X axis. Then I scale the box down along the Y axis, I move the box up select the bottom faces and extrude them down along the Z axis to get the wrist of the hand. Then I delete the faces where the first finger would go, then like the foot I make a circle which has 6 edges, I scale it down to be about the same size of a finger and then I extrude it upwards along the Z axis. I then Loop cut Twice on the finger to get the joints, and then I make two more loop cuts on each joint one above both Joints and one below to make supporting edges. I face off the top of the ...
Read more

Week 20

Image
Now that the Hair is done it is down to the last part of modelling which will be the cloths. I looked at 2 AM for his tutorial on how he makes cloths for his characters, he looked at games like Genshin Impact, and Honkai Star rail and how they design their characters outfits, and used some of the same methods to create an outfit for his character.  (39) He made the cloths by either selecting some parts of the body and then duplicating it, and separating it to get the cloths, or he made certain parts from scratch like the jacket, or the chains. This video is very helpful as I wouldn't know where to start on making cloths, but this video helps clear things up and simplifies it in a way which makes it easy to understand how to make an outfit.   Although I have a modelling sheet for my character and I have been following some of it and changing other parts, I was thinking that I could change the clothing or the theme of the character to something different, the first Idea was...
Read more